Close
You have no items in your shopping cart.
Search

Tundra Catch Can Kit, 2007+ - Radium

Manufacturer: Radium Engineering
SKU: RA-CC-KIT-Tundra
281.65 EUR
Incl. 21% VAT (Netherlands) | Change

Tundra Catch Can Kit, 2007+

Read about the different kit options below

*
Availability: Please select required attribute(s)
+ -

This installation kit was specifically designed for the 2007+ Toyota Tundra with the 3UR-FE engine. There is no drilling or permanent modifications required. IF USING A TRD OR OTHER AFTERMARKET SUPERCHARGER, please check the pictures carefully to make sure the location of the catch cans is not occupied by intercooler plumbing or other related supercharger components.

An oil catch can is essential on a performance vehicle to protect the engine from elevated levels of crankcase blow-by accumulated from everyday driving. Excess oil-saturated air circulating back into the air intake stream can lead to degraded performance. Radium Engineering catch cans feature large 10AN ORB ports, a 4AN ORB drain port, 2-step oil separation baffling, and an O-ring sealed dipstick.

Features:

  • Effectively raises the octane and increased engine performance from cleaner inlet air
  • Prevents oil buildup in the intake or intercooler system walls, throttle body, intake manifold, etc.
  • Excessive oil collection can be an indicator of a damaged engine.
  • Lowers hydrocarbon emissions
  • Capacity: 6 fluid ounces
  • Height (without fittings): 5 inches
  • Outside Diameter: 2.45 inches

TUNDRA CATCH CAN KIT OPTIONS

Radium Engineering offers two independent Tundra oil catch can kits that are sold individually or together. They do NOT vent to the atmosphere (VTA), thus are emissions and track legal. Closed-loop systems route clean filtered air back in through the engine to be burned and to promote negative crankcase pressure for optimal performance. Furthermore, closed systems prevent unwanted oil vapors from entering the cabin.

  • The 20-0238 PCV Catch Can Kit runs in line with the PCV (positive crankcase ventilation) valve. When the intake manifold pressure is close to or greater than atmospheric pressure, the PCV "check" valve closes and, thus, this hose experiences no flow. Conversely, the PCV hose will experience a "metered" vacuum when the engine is idling, low load cruising, and decelerating. This would normally draw unwanted crankcase vapor, unspent fuel, and oil sludge into the intake manifold immediately after a high load run. Note: Because the Radium catch cans are pressure sealed, they are great for boosted applications as well so connecting to the intake manifold is permitted.

  • The 20-0239 Crankcase Catch Can Kit comes with 2 mounting brackets. One bracket will be disregarded depending if the PCV kit will also be used. The crankcase vent runs in line with the 1/2" valve cover breather port. At low loads, it experiences atmospheric pressure, but when the engine is at high load (WOT), this hose will experience vacuum and would normally be drawing unwanted crankcase vapors, unspent fuel, and oil sludge into the air filter intake pipe. If the engine is turbocharged or supercharged and you are finding oil accumulation stuck in the intercooler, this catch can is a necessity as oil will lower the thermal efficiency properties of the heat exchange process.
  • For the ultimate in engine protection, Radium recommends the Tundra 20-0240 Dual Catch Can Kit (shown below) which utilizes both the "Crankcase" catch can and "PCV" catch can.

----------------------------------------------------------------------------

  • PCV Kit Includes:

Billet oil catch can with integrated condenser and dipstick
Tundra-specific laser cut anodized mounting bracket
Anodized aluminum 6AN and 8AN hose ends
Anodized 6AN and 8AN adapter fittings 
Stainless steel mounting hardware 
PCV rubber hose  

--------------------------------------------------------------------------------

  • Crankcase Vent Kit Includes:

Billet oil catch can with integrated condenser and dipstick
Tundra-specific laser cut anodized aluminum mounting bracket
Laser cut anodized aluminum mounting bracket
Anodized aluminum 8AN hose ends and adapter fittings
Enough 1/2" PCV rubber hose to mate to custom applications  
Stainless steel mounting hardware

Products specifications
Product TypeCrankcase Ventilation
EngineToyota 3UR-FE
MakeToyota, Toyota, Toyota
ModelSequoia, Tundra, Land Cruiser

At CBS Racing, happy and satisfied customers are our top priority.

We do not hide behind supplier or manufacturer warranty statements like: "No warranty on racing products". This is not okay! There must be a guarantee and a warranty on all products sold - they must work and fit your car as advertised.

We take great care in selecting what we sell and what we install on our build- and customer cars. So you can rest assured we got your back, and we will not leave you stranded with a bad or broken part.

At CBS Racing, we strive to be the first shop of choice for our fellow car enthusiasts!
And we plan to do that by taking care of our customers the way they deserve and deliver 110% service, always!

Thanks for trusting us!

Write your own review Close Review Form
  • Only registered users can write reviews
*
*
Bad
Excellent
*
*
*
*